Description,PLC tag,Value,"Setup word
DINT[100]",Comment
Look-up table for angle linearisation 90-95deg,Apron_Offset[0],0.5,SetupWord[0],SetupWord is integer = real value *100
Look-up table for angle linearisation 95-100deg,Apron_Offset[1],0.6,SetupWord[1],SetupWord is integer = real value *100
Look-up table for angle linearisation 100-105deg,Apron_Offset[2],0.6,SetupWord[2],SetupWord is integer = real value *100
Look-up table for angle linearisation 105-110deg,Apron_Offset[3],1.0,SetupWord[3],SetupWord is integer = real value *100
Look-up table for angle linearisation 110-115deg,Apron_Offset[4],2.0,SetupWord[4],SetupWord is integer = real value *100
Look-up table for angle linearisation 115-120deg,Apron_Offset[5],3.0,SetupWord[5],SetupWord is integer = real value *100
Look-up table for angle linearisation 120-125deg,Apron_Offset[6],5.0,SetupWord[6],SetupWord is integer = real value *100
Look-up table for angle linearisation 125-130deg,Apron_Offset[7],9.0,SetupWord[7],SetupWord is integer = real value *100
Look-up table for angle linearisation 130-135deg,Apron_Offset[8],9.0,SetupWord[8],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[9],0.0,SetupWord[9],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[10],0.0,SetupWord[10],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[11],0.0,SetupWord[11],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[12],0.0,SetupWord[12],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[13],0.0,SetupWord[13],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[14],0.0,SetupWord[14],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[15],0.0,SetupWord[15],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[16],0.0,SetupWord[16],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[17],0.0,SetupWord[17],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[18],0.0,SetupWord[18],SetupWord is integer = real value *100
Curremtly not used,Apron_Offset[19],0.0,SetupWord[19],SetupWord is integer = real value *100

Angle calibration value,Angle_Calibration,158,SetupWord[20],
Angle limits,Angle_max,133,SetupWord[21],
Angle limits,Angle_min,0,SetupWord[22],
Apron UP creep speed,Apron_REV_CREEP_speed,-1000,SetupWord[23],
Apron UP maximum speed,Apron_Speed_limit,6000,SetupWord[24],
Apron DOWN gain,ApronDown_Gain,0.35,SetupWord[25],SetupWord is integer = real value *100
Apron DOWN creep speed,ApronDownCREEP_speed,700,SetupWord[26],
Apron DOWN maximum speed,ApronDownSpeed_limit,5000,SetupWord[27],
Apron UP gain used below gain change angle,ApronUp_Gain,0.55,SetupWord[28],SetupWord is integer = real value *100
Apron UP CREEP speed used below gain change angle,ApronUpCreepHigh,-1000,SetupWord[29],
Apron UP CREEP speed used above gain change angle,ApronUpCreepLow,-400,SetupWord[30],
Apron UP gain used above gain change angle,ApronUpLowGain,0.55,SetupWord[31],SetupWord is integer = real value *100

Backgauge calibration value,Backgauge_Calibration,-1200,SetupWord[40],
Backgauge FORWARD speed in RPM,Backgauge_FWD_speed,800,SetupWord[41],
Backgauge REVERSE speed in RPM,Backgauge_REV_speed,2000,SetupWord[42],

Clamp calibration,Clamp_Calibration,100,SetupWord[50],
Clamp position error at which speed switches to creep,Clamp_creep_Neg,-15,SetupWord[51],
Clamp position error at which speed switches to creep,Clamp_creep_Pos,15,SetupWord[52],
Clamp CREEP speed (when inside above values),Clamp_Creep_speed,2500,SetupWord[53],
Offset value so clamp height reads zero at pressure,Clamp_Offset2,4,SetupWord[54],
Clamp HIGH speed,Clamp_speed,7500,SetupWord[55],
"Value below which ""HALF CLAMP TOO LOW"" comes on",HalfClampMin,10,SetupWord[56],
Clamp High creep speed to gain clamp pressure more quickly,ClampCreepHighSpeed,2500,SetupWord[57],

Pump speed on ESTOP (x100 Hz),ESTOPSpeed,5000,SetupWord[60]
Pump idle speed (x 100Hz),Hyd_Pump_Idle_speed,500,SetupWord[61]

Slitter CREEP speed,Slitter_CREEP_speed,800,SetupWord[70]
Slitter FORWARD speed in full speed mode,Slitter_FAST_speed,5000,SetupWord[71]
Slitter RETURN speed in full speed mode,Slitter_RETURN_speed,5500,SetupWord[72]
Slitter FORWARD speed in half speed mode,Slitter_SLOW_speed,2500,SetupWord[73]
Alarm timer settings for sensor checks,SlitterFullSpeedFastTime,10000,SetupWord[74]
Alarm timer settings for sensor checks,SlitterFullSpeedSlowTime,3000,SetupWord[75]
Alarm timer settings for sensor checks,SlitterSlowSpeedFastTime,20000,SetupWord[76]
Alarm timer settings for sensor checks,SlitterSlowSpeedSlowTime,5000,SetupWord[77]
"Set to 1 to enable ""hold foot on pedal mode"" for slitter",B_SlitterHoldToRun,1,SetupWord[78]

,,,53